Loading... Please wait...

Categories

Our Newsletter


Sort by:

Mercury Outboard Racing

  • Bayer 4 Cylinder Exhaust Plate, 30 40 44ci, Used
    $150.00 Bayer 4 Cylinder Exhaust Plate, 30 40 44ci, Used
    Nice shape, missing one stud.  It has 1/4" mounting holes.  If you need it on later blocks with 5/16 holes you will need to open up the mounting holes.

  • 717-5050A1 Piston, Mercury 15 - 30ci, 30H, .030, NEW
    $125.00 717-5050A1 Piston, Mercury 15 - 30ci, 30H, .030, NEW
    New 15/30ci piston, .030.  Series 717-1182.  Very hard to find.  No rings, pin or clips.  Flat top style.

  • 31-85114, 31-85113 25XS Type Roller Bearings, Used
    $25.00 31-85114, 31-85113 25XS Type Roller Bearings, Used
    Here's upper and lower, good to run, used crank roller bearings...

  • $50.00 630-8835A2 A4 25XS Type Rod
    Merc 25 rod, same as used on the 25XS motors.  Rod is in excellent condition.  Casting number is 630-7080.  From Mercury they cost $235.00 each...

  • 42471 25XS Reed Block Assy, Used
    $25.00 42471 25XS Reed Block Assy, Used
    Merc 25 reed block assembly.  Same as used on the 25XS.  Part is in real nice shape...

  • 11139A1 25XS Type Co-Pilot Kit, Used
    $40.00 11139A1 25XS Type Co-Pilot Kit, Used
    .Merc 25 co-pilot kit.  Same as used on the 25XS clamp assemblies.  Good used condition...

  • 86992 25XS Type Center Main, Used
    $50.00 86992 25XS Type Center Main, Used
    Merc 25 center main bearing set.  Same as used on the 25XS motors, now NLA from Mercury.  This is in excellent condition...

  • MERCURY OUTBOARD RACING 25XS CARB - USED
    $175.00 MERCURY OUTBOARD RACING 25XS CARB - USED
    SERVICE MOTOR CARB CONVERTED TO A 25XS LINKAGE. IT DOES NOT HAVE A FULL BUTTERFLY. MAY OR MAY NOT NEED A SERVICE KIT.

  • Merc Racing Flywheel Hub - 44XS
    $25.00 Merc Racing Flywheel Hub - 44XS
    If you are going to run a V6 aluminum flywheel on your 44XS, you will need a hub like this.

  • Mercury Racing Rope Shive - Used
    $20.00 Mercury Racing Rope Shive - Used
    Steel, 5/16 mounting holes.  Works fine on a Merc Mod Motor.

  • Mercury Racing Rope Shive
    $20.00 Mercury Racing Rope Shive
    Steel, 1/4 mounting holes.  Works fine on a Merc Mod Motor.

  • 40H 55H Type Clamp Assembly
    $375.00 40H 55H Type Clamp Assembly
    Will go right on a 55H leg.  It is set up for a 55 leg so it has no holes drilled in the co-pilot to anchor to a 40H leg.  You will have to drill two holes if needed.  It is in very nice shape, has no thrumb...

  • 20H Popper Conversion Set Up
    $1,500.00 20H Popper Conversion Set Up
    In as raced condition.  Bottom swivel pin bushing would need to be replaced.  Thumb screws are in okay condition, pads are loose.  It is complete.  Serial tag #786945.  Comes with filler block and...

  • Quincy 20H Alky Split Crank Case
    $750.00 Quincy 20H Alky Split Crank Case
    Extremely rare.  Designed for Alky racing but this split case design works very well on a 20H for the serious builder.  There are 2 reinforcement welds on top of the case.  See photo.  No cracks or damage...

  • Merc 200 Block From 25SS
    $150.00 Merc 200 Block From 25SS
    Merc 200 block from a 25SS.  It is bored .015, cylinder walls are nice, should be honed for clean up.  On the crank case there is a weld by the intake and the boss for the rear recoil starter has been welded. ...

  • Merc 200 Crank From 25SS Block
    $150.00 Merc 200 Crank From 25SS Block
    Merc 200 crank from a 25SS block, nice shape.  The first couple of threads are nicked, you can dress them up if you like.  The nut does thread on.  Crank is marked Jon, May 20, 1977?